BS EN IEC 62932-1-2020 pdf download.Flow battery energy systems for stationary applications – Part 1: Terminology and general aspects (IEC 62932-1:2020).
This part of IEC 62932 relates to flow battery energy systems (FBES) used in electrical energy storage (EES) applications and provides the main terminology and general aspects of this technology, including terms necessary for the definition of unit parameters, test methods, safety and environmental issues.
2 Normative references
There are no normative references in this document.
3 Terms, definitions and abbreviated terms
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1.1 ambient temperature
environmental temperature around a flow battery energy system
3.1.2 auxiliary energy
energy consumed by all the auxiliary equipment and components of a flow battery and of a flow battery energy system
Note 1 to entry: The equipment and components include, but are not limited to, battery management system, battery support system, fluid circulation system.
3.1.3 battery management system
BMS electronic system associated with a flow battery energy system which monitors and/or manages its state, calculates secondary data, reports that data and/or controls its environment to influence the flow battery energy system’s performance and/or service life
Note 1 to entry: The function of the battery management system can be fully or partially assigned to the battery pack and/or to equipment that uses flow battery energy store systems.
[SOURCE: IEC 61 427-2:201 5, 3.8, modified – admitted terms “battery management unit” and “BMU” omitted, “battery” replaced by “flow battery energy system”, Notes 2 to 4 deleted.]
3.1.4 battery support system
BSS auxiliary units, such as heat exchanger, ventilation system, safety system, and inert gas system, used in an FBES, and which are not stacks, or part of the fluid circulation system, power conversion system, or battery management system
Note 1 to entry: The battery support system is controlled by the battery management system.
3.1.5 charge
charging
<of a battery> operation during which a secondary cell or battery is supplied with electric energy from an external circuit which results in chemical changes within the cell and thus the storage of energy as chemical energy
Note 1 to entry: A charge operation is defined by its maximum voltage, current, duration and other conditions as specified by the manufacturer.
[SOURCE: IEC 60050-482:2004, 482-05-27, modified – term “charging of a battery” separated
into “charge” and “charging” with “of a battery” as the domain, and addition of the note.]
3.1.6 cold standby
standby state requiring warm up before a demand to operate can be met
Note 1 to entry: A cold standby state may apply to redundant or stand-alone items.
Note 2 to entry: In this context “warm up” includes meeting any conditions required to operate as required (e.g. achieving the required temperature, speed, pressure).
[SOURCE: IEC 60050-1 92:201 5, 1 92-02-1 1 , modified – “state” omitted from the term, and the domain, “of an item”, deleted.]
3.1.7 discharge
discharging
<of a battery> operation during which a secondary battery supplies electric energy to an external circuit which results in chemical changes within the cell and the release of energy as electrical energy
Note 1 to entry: A discharge operation is defined by its maximum voltage, current, duration and other conditions as specified by the manufacturer.
3.1.8 emergency shutdown
rapid regulated shutdown of the flow battery energy system triggered by a protection system or by manual intervention
[SOURCE: IEC 60050-41 5:1 999, 41 5-01 -1 1 , modified – the word “regulated” added, and “wind turbine” replaced by “flow battery energy system”.]
3.1.9 emergency stop
function which is intended to avert arising or reduce existing hazards to persons, damage to machinery or to work in progress and be initiated by a single action
[SOURCE: ISO 1 3850:201 5, 3.1 , modified – “(E-Stop)” omitted from the term, second preferred term “emergency stop function” omitted, layout modified.]BS EN IEC 62932-1 pdf download.